Plumbers in Fort Worth, TX – If you have come across this article because your toilet is running then you should probably quit reading and go catch it. All joking aside, a running toilet can be an annoying experience as well as a costly one if it is left unattended. Professional plumbers in Fort Worth, TX deal with running toilet repairs every single day of the year. Running toilets are one of the most common plumbing problems that plumbers in Fort Worth, TX deal with. The ongoing steady stream of water flowing into the toilet is bowl is typically due to a component inside of the toilet tank called a ballcock that does not shut off at the end of a flush cycle. If this is left unattended and not taken care of right away it could lead to hundreds if not thousands of gallons of water wasted and exponentially increase the next month’s water bill tremendously. In this case scenario if you do not have the time or confidence in doing the repairs yourself you should seek out professional plumbers in Fort Worth, TX to help you with the repair.
Diagnosing the Problem
Taking off the lid of the toilet tank you will notice a round vertical cylinder typically located in the center or on the left side of the tank. This is called the overflow tube. As you watch, if you see water to continue to flow down over the lip of the tub, then most likely the water supply valve, more commonly referred to as the ballcock by plumbers in Fort Worth, TX, this will need to be adjusted so it shuts off when the water level is at a low level.
It tends to be unusual for a ballcock, also known as a water supply valve to suddenly be misadjusted. In all likelihood the ballcock has become worn out and will need to be replaced. This is a rather simple task but if you are unsure of what to do then you will need to look for professional plumbers in Fort Worth, TX to handle this for you.
Inspect the Flapper Chain
In the event that you do not notice a problem with the overflow tube or the ballcock then you should next inspect the flapper chain. This is relatively easy to find as it will be a chain that is connected to the toilet’s flushing lever with the flapper flush valve which will be located at the bottom of the toilet’s tank.
Usually there should not be a problem with the chain unless it was replaced recently. Otherwise, you would have had this problem before. However, if the chain is too short, it may not be allowing the flapper to fully drop down into the opening of the flush valve when the flush cycle concludes. If this is the case then this will allow water to continuously flow down into the tank. On the other hand, in the event that the chain is too long, it may get stuck under the flapper, preventing the flapper from sealing itself after the flush cycle has concluded.
Whatever the case, this too is a very simple fix and all that will need to be done is simply adjust the length of the chain so that it is neither too long nor too short. Once again if you are unsure of what you are doing you can always seek out professional plumbers in Fort Worth, TX to do the job for you.
Assess the Flapper Seal
The final problem with a toilet running may be the flapper seal itself. When flappers age, they can become harden or warped to the point that they do not provide a good seal anymore. Even with just a slight warping of the seal can cause the toilet to continuously drain water into the bowl. To determine if this is the case a simple test is to drop a few drops of food coloring into the tank and sit back and watch whether the water in the bowl begins to change color.
If after a few moments the water in the bowl begins to change color then you can confirm that the problem lies with the flapper seal and it will need to be replaced. If this is the case, it is also a relatively simple task to do. However, if you are uncomfortable or unsure then you can seek out professional plumbers in Fort Worth, TX to get the job done for you.
In the event that you do one of these repairs on your own and it is obvious that the components are rather old, you may consider just replacing all of the components inside of the toilets with new parts. Replacing a component that has failed due to age will mean that sooner or later it is most likely than other components within the tank will fail also. By going ahead and replacing all of the old components at once you will save yourself from needing to replace others down the road. However, if you are not certain on how to make these repairs yourself, or you are scared of doing more damage, you can seek out professional plumbers to do it for you.
About Benjamin Franklin Plumbing in Arlington, Texas
Benjamin Franklin Plumbing in Arlington, TX has professional plumbers in Fort Worth, Texas servicing Fort Worth and surrounding areas. Our experienced, courteous and friendly plumbers provide on time plumbing related services to not only Arlington but surrounding areas also. If you are in need of a professional plumber that you can count on for plumbing repairs, maintenance and / or installation then you can count on us at Benjamin Franklin Plumbing in Arlington, Texas.
Ben Franklin Plumbing is a leader in the field for plumbing related repairs. We are also one of the most trusted plumbing service brands in the industry with high standards of service that you can rely on. When you contact us you can rest assured knowing that you are receiving the best plumbers in Fort Worth, Texas. Our commitment to service and excellence is reflected in our stone solid A+ rating with the Better Business Bureau. If you have a plumbing related problem in your home or business and you need help, do not hesitate to contact us today. Our professional, courteous and friendly plumbers in Fort Worth, Texas will be more than happy to assist you and answer any of your questions and schedule an appointment with you to assess the plumbing related problem and resolve it at your earliest convenience. Give Benjamin Franklin Plumbing in Arlington, Texas a call today if you are looking for professional plumbers in Fort Worth, Texas. If there’s any delay, it’s you we pay®