Low-flow toilets are an important part of sustainable living, helping us conserve water and save money on our water bills. However, sometimes these toilets don’t have enough flushing power to do the job effectively. When this happens, the toilet can start to smell and become clogged. Fortunately, some simple ways are recommended by professional plumbers in Burleson, TX that can increase the flushing power in a low-flow toilet. This article will discuss some of these strategies to help you improve flushing power in a low-flow toilet. Read on to learn.
Replace the Toilet Flapper
One of the most effective ways to increase flushing power in a low-flow toilet is to replace the toilet flapper. The flapper is a valve that seals off the tank from the bowl and allows water to pass through when it’s opened. Over time, this valve can become worn or clogged with debris, reducing the amount of water released into the bowl. Replacing your toilet flapper with a newer, more efficient model can help improve the flushing power of your low-flow toilet. When shopping for a new flapper, make sure to look for one that is specifically designed for low-flow toilets. You should also hire a professional plumber in Burleson, TX to install the new flapper, as this is not a DIY job.
Adjust the Water Level in the Tank
Another way to increase flushing power in a low-flow toilet is to adjust the water level in the tank. On some models, you can do this by adjusting an internal float that controls how much water flows into the bowl. Generally, the water level should be set one inch below the overflow pipe in the tank, which allows enough water to fill up the bowl rapidly, creating powerful flushing pressure. While adjusting the water level in the tank is a simple job, it’s best to hire a professional plumber for this task, as it can be difficult to access the internal float on certain models. Sometimes, you may need to replace the float if it’s damaged. That is why it’s best to leave this job to the professionals.
Install a Dual-Flush Toilet
A third way to increase flushing power in a low-flow toilet is to install a dual-flush model. Dual-flush toilets are designed with two separate buttons: one for a full flush and one for a partial flush. The full flush will release more water into the bowl, creating powerful flushing pressure and effectively rinsing away waste. Meanwhile, the partial flush is used for liquid waste and uses less water. If the full flush isn’t enough to effectively clear the bowl, you may need to upgrade your toilet to a more powerful model.
Clean the Toilet Tank
Cleaning the toilet tank regularly is an important part of toilet maintenance that many homeowners overlook. Doing so, however, can have multiple practical benefits for your low-flow toilet system. While you may already be aware of how removing any obstructions from the bowl will increase flushing power, there are further advantages to keeping it clean with a good scrubbing every few months. Not only will this improve performance and extend your toilet’s lifespan, but it can also cut costs associated with frequent clogs. While cleaning the tank might seem simple, hiring a professional plumber is the best way to go.
Install a Toilet Booster Pump
One important upgrade for any low-flow toilet is installing a toilet booster pump. A booster pump utilizes air pressure to add suction and flow to the plumbing system, helping it flush waste more quickly and efficiently. It’s an ecological solution that not only boosts the performance of low-flow toilets but also reduces water consumption while doing its job more effectively. You’ll need a professional plumber for this task, as installing a booster pump is complicated and requires specialized expertise.
Upgrade to a Higher Capacity Toilet Tank
If you have a low-flow toilet and have to flush it multiple times before the bowl is cleared, then it might be time to upgrade your toilet tank with one with a higher capacity. Increasing the tank’s water will make more flushing available each time without being too wasteful. This upgrade can also help to conserve water since you won’t be using excess water out of frustration when attempting to clear the bowl in your current tank. Why not hire a plumber today to help you switch to a higher-capacity tank?
Replace the Entire Toilet System
Finally, if all else fails, you may need to replace the entire toilet system. This is a more expensive option and should only be considered a last resort. Many modern toilets today are built with innovative technologies like dual flush or pressure assist, giving greater control over how much water is used while maximizing performance. In addition, replacing an old low-flow toilet with a newer model can help reduce the cost of your water bills. Before proceeding with this solution, it’s important to consult an experienced plumber to determine whether or not it’s necessary. A professional plumber can provide you with an honest assessment of your toilet’s condition and suggest the best course of action.
Overall, there are many ways to increase flushing power in low-flow toilets. From installing a new flapper valve and adjusting the water level in the tank to installing a dual-flush toilet or toilet booster pump, all of these options can help improve performance and conserve water. But before doing any of these modifications, consult a professional plumber in Burleson, TX for expert advice. They can assess your situation and provide the best solution for your needs.
We Are the Plumbing Experts to Consult
At Benjamin Franklin Plumbing of Fort Worth, we have the expertise and experience to help you get the most out of your low-flow toilet. From diagnosing problems to providing advice on improving flushing power, our team is always ready to provide professional plumbing services. Contact us today for a free consultation.