Every Step Counts – Water Heater Installation by a Professional Plumber in Fort Worth, TX
Water heaters standout amongst the most basic, yet overlooked appliances in any home. They represent around 25% of all your utility charges so they’re doing a great deal of work.
Usually, the standard water heater tank has a lifetime of 8-12 years. This clearly means that installation of a water heater is not a frequent task but happens in years.
Likewise, it also means that, with the recurring changes in techniques, methodology and upgradation in appliances industry nowadays, the best and most convenient option is NOT to take up the task as a DIY project but to hire a professional plumber in Fort Worth, TX.
Newly installed water heaters are usually unproblematic. The elements and parts of water heaters are easily available in market at reasonable prices, however; this should not be the reason for you to stay away from hiring a professional plumber in Fort Worth, TX. A wise decision is to take the assistance of an expert professional plumber in Fort Worth, TX from the start.
Consider having interrupted electric power, wrong voltage or improper home wiring and connection. Would you be able to handle this issue at the time of installing a water heater by yourself? Or would you consider handing over the newly unpacked water heater to a professional plumber in Fort Worth, TX, to handle the way, it deserves to be? The last one will surely make yours and your water heater life much easier.
Smart Steps of Water Heater Installation by a Professional Plumber in Fort Worth, TX
Here are the steps that must be followed for water heater installation to avoid the repairs and maintenance cost in near future.
Also, this will help you understand the expertise and tools required by plumbers in Fort Worth, TX, in carrying out the installation process.
From Unpacking to Checking the Home Connections
For a perfect start, it is essential for a plumber in Fort Worth, TX to make sure that these steps are properly followed:
- Before unpacking the water heater, recheck the water supply, gas supply and vent positioning and their functionality.
- Ensure the availability of required tools. This includes 3 bits nut driver or a drill, pipe joint compound, pencil, measure tape, screws, small bucket, a utility knife and a spray bottle.
- Unpack the water heater using a utility knife and cutting at the given line. Carefully, place your water heater on a dolly and position it correctly. This is important to ensure that control unit or wires are not damaged in following this step.
- Take measurement for earthquake strap. These should be two of them at top and bottom each. The first one should be under the T&P valve and the second one at the top of the pilot control.
Making the Strong Connections to Avoid Leak
In order to avoid gas or water leak, it’s time to make the strong connections during your water heater installation process.
- Connect the water supply using flexible copper supplies to avoid soldering connections. Keep the water supply (wall valve) closed and place bucket below to avoid spilling water on water heater surface. Make tight connections to avoid leaking.
- Install the vent hood with the help of screws. When you push it down, you will hear a clicking sound, confirming its correct positioning.
- Put the vent pipe in. In the case of using the old one, make sure it does not have any holes or cracks. Attach the adjustable elbow and keep them in line to make it look good.
- Connect the gas supply and make sure its valve is closed. Join the flex connector using pipe joint compound, with the control unit. Don’t put too much pressure on the control unit, while placing it.
Filling up the Water Heater and Checking for Results
After making the required connections, let’s fill up the tank with water and check the results of your efforts.
- Fill the water into the water heater. It is recommended to attach the earthquake straps after this step as the water heater is pretty light when there is no water in it. Check for the leaks once the tank is filled with water.
- It’s time to connect the earthquake straps and avoiding pulling it too tightly.
- Attach the pipe with a T&P relief valve to discharge excessive water. Use pipe joint compound to ensure its strength. Always keep it 6 inches off the floor.
- Now it’s time to turn the gas connection ON. Light the pilot and this is done by turning the gas shut off valve to the ON position. Take the front cover at the bottom, off by lifting it. Turn ON the pilot mode and ensure the dialer is at pilot lightening.
- Press down the pilot valve to let the gas pass for few seconds. Press the green button one or two times (continuing to hold the pilot down for 45 seconds). Check if the flame is on. Now release the pilot valve and ensure, the pilot is still lit. Now simply turn the pilot to ON position and adjust the dial for your desired heat level.
- Lastly, always check for gas leaks by spraying soapy water on all connections. In the case of any leak, you would notice bubbles at the surface, indicating a weak connection.
Following these tips from a professional plumber in Fort Worth, TX, your water heater installation process can be done in just half an hour.
If you are still thinking to get the installation done on your own then make sure you have the required expertise and tools to afford the instructions above. Otherwise, you would end up hiring a professional plumber in Fort Worth, TX, once it’s too late.
If you are located in Fort Worth, TX then explore the portfolio of Benjamin Franklin Plumbing Fort Worth. They offer the expert technicians to challenge all of your commercial and residential plumbing needs. From simple to complex, large to small jobs, their expert plumbers in Fort Worth, TX is your ultimate solution.
Sources
http://www.fastwaterheater.com/water-heaters/articles/potential-causes-reduced-hot-water/
http://www.fastwaterheater.com/water-heaters/water-heater-basics/
https://www.familyhandyman.com/plumbing/water-heater/replacing-a-water-heater/view-all
