Blog

The plumbing system installed in your home follow the laws of nature. Pressure, gravity, water are some of the many factors of the plumbing system in a house. Knowing that, you must understand that the plumbing system in a house is intricate and involves a lot of fixes from time to time.

If you are aware of the plumbing basics or if you ensure the regular repair and maintenance of the plumbing system by hiring plumber in Fort Worth, TX then you can save a lot of time, trouble and money.

The Two Separate Subsystems of Your Plumbing System

As per the plumbers in Fort Worth, TX, the plumbing of your house comprise two basic and separate subsystems. One of them is responsible for bringing freshwater in and another one is responsible to drain the wastewater.  The water you receive in your house is under pressure. It enters your house under enough pressure to easily travel upstairs and around corners.

When water enters your house, your meter registers the amount of water passing through.  Generally, the main stop or water shut off valve is located near to the meter. That is why as you face a plumbing emergency in your home, the most recommended measure by a plumber in Fort Worth, TX is to shut off the main valve. Otherwise, it can lead to in-house flooding instantly.

However, if the water leakage is limited to your sink, bathtub or toilet then you should not shut off the main water valve instead call the assistance of plumber in Fort Worth, TX to fix the issue permanently.

The Hot Water Supply

The water that comes from the main supply is always available for your routine stuff or cold water needs.  However, when you need hot water in your house, it needs another step. To get hot water in your house, a water pipe carries the cold water from the main line to your water heater. Once the water is heated by the water heater, the hot water line coming from the water heater takes this heated water to all outlets, fixtures, and appliances.

As per the plumber in Fort Worth, TX, the thermostat located in your water heater system is responsible for heating the cold water as per the defined temperature.  The thermostat maintains the temperature when you use the turning device to adjust the heating element on and off.  Generally in a home setup the plumber in Fort Worth, TX suggest keeping the temperature maintained between 140F to 160F.

If you maintain the temperature at around 120F that it is also economical in a home set up.  Some of the latest models of appliances or especially dishwaters might need higher temperature water. On the other hand, some dishwater is now having a built-in water heater that itself boost the temperature by 20 – 30 degrees.

The Drainage System

According to plumbers in Fort Worth, TX, regardless if your house is on septic or sewer system, the overall system is essentially the same. Just like the supply system, the drainage system in your house does not need pressure. Instead, when a plumbing system is installed by a professional plumber in Fort Worth, TX, the wastewater leaves the home by using drainage pipes that are angled or pitched downwards. Gravity is the factor that comes to play and pulls the waste. The downward flow is then continued by sewer line to a septic tank or sewage treatment facility.

This may sound like a simple system, but there is a lot more to it. The system is complex and only professional plumber in Fort Worth, TX, can handle the complexities involved in a plumbing system. Some of the major areas of your plumbing system include the traps, vents and clean outs. The vents let the air to pass through the drainpipes. The vent is generally located on the roof. Hence if when you face an air blockage from the vents, the wastewater will not flow out completely and the accumulated water in the traps will need to be drained off.

When we speak of a drainage system, traps are one of the most vital components. There is a trap under every sink. It is an S-shaped or curved pipe section under a drain. When water passes through the basin with pressure, it passes through the trap and gets out from the drainpipe. But some amount of water still remains in the trap to form a seal and to avoid sewer gas from backing up in your house. As per the plumber in Fort Worth, TX, this is the main reason why every sink in your house has a trap.

The toilets in a house are self-trapped and need no additional trap. Bathtubs usually have drum traps. They not only create a seal to avoid sewer gas but also accumulate dirt and hair in order to avoid clogged drains. Kitchen sinks come with grease traps that collect the grease which usually results in clogging. The professional plumber in Fort Worth, TX state, hair, and grease are the major causes of drain clogs. However, traps usually come with clean-out plugs that allow you to easily break or remove the blockage.

In the bottom line

The plumbing system in your house is a complex and intricate system. It needs a lot of maintenance to continue to work properly. The blockage is one of the most commonly faced problems with many homeowners and results due to improper usage of sinks, bathtubs or toilets.

It is important to maintain your plumbing system by getting it inspected regularly. For this, you should only take the assistance of professional plumber in Fort Worth, TX. To get the best quality service head over to Benjamin Franklin right away. They are best known for the quality of service. Their team of professionals is well-versed in handling the most complex plumbing issues.

You can also contact them or take their immediate assistance by simply calling on their 24/7 emergency number available on their website.