Blog

Whether you’re a homeowner or a commercial owner you’d agree that broken pipes are a major source of inconvenience. Broken pipes inside or outside your facility can interrupt your business operations and bring it to a standstill long before a plumber in Arlington, TX visits your facility and resolves the problem. Besides this, when water supply pipes break, they can wreak havoc. Water can inundate your home or facility; and inflict severe damage to your valuables, assets and structure.

Studies show that the water loss potentially can be around 400 liters when pipes burst or break. And that is equivalent to having 2 full baths in an hour. In other words, if the problem is not addressed timely by calling a plumber in Arlington, TX for a repair job, you can have nearly 48 full water baths or about 9,600 liters of water in your premises in a day due to burst or broken water pipes.

Though there can be many reasons for broken and burst water pipes, here are some of the top ones:

Reason#1— Freezing Temperatures

Freezing temperature is perhaps the most common and top reasons for broken pipes. Water supply pipes tend to burst when they exposed to freezing temperatures. When they come into contact with air below 28° F, the pipes freeze and eventually, rupture. Pipes located in unconditioned areas such as attic or crawl spaces are at higher risk.

During winter season, ice tends to buildup in water pipes and so does the pressure inside it. As the ice puts pressure on the pipes, and the pressure also increases, all then results into pipe burst or breakage. Most often pipes break from the weaker or middle joints and as most piping in the home or commercial facilities are hidden in roof spaces or walls, bursting of the pipes can be devastating and cause serious structural damage. This is an emergency situation and requires a quick plumbing job. Therefore it’s extremely important that you get in touch with Benjamin Franklin Plumbing and call an experienced plumber in Arlington, TX immediately, without any delay. They offer emergency plumbing services round the clock.

Reason#2— Water Pressure

Generally, the water supplied by the municipal through the water line is of very high pressure.  A pressure regulator is therefore used at the meter to lower the water pressure bringing it to a safe level of nearly 40 to about 50 psi. This helps ensures that the household plumbing does not get damaged due to high pressure.

However, sometimes the pressure regulator is either defective or is not installed/adjusted properly and thus fail to regulate the water pressure level correctly. Failure to regulate the water pressure may raise the pressure high enough causing the water pipes to rupture and eventually, burst.

When this happens, it is advisable to call a plumber in Arlington, TX right away before serious damage is done. An experienced plumber in Arlington, TX is well-trained to handle such situations. The plumber will quickly check the regulator and attach a gauge to it to check the pressure. If problems with the regulator are detected, the plumber will replace it and repair the pipes, resolving the issue immediately.

Reason#3— Clogging

Another top reason for pipe burst and breaks is clogging. Pipes can get clogged due to several reasons like accumulation of debris such as leaves or sediments inside them or tree roots penetrating into the pipe lines. And if you don’t clean the pipes and remove debris from it routinely, they can get clogged badly and soon enough, burst. If you feel that the water supply has slowed down in your pipes, this could be because of clogged pipes. It is advisable to call a plumber in Arlington, TX to inspect the pipes before they burst and break.

Reason#4—Corrosion

Both galvanized and copper pipes are prone to corrosion. Corrosion causes the pipes to degrade, leading them to fail. One of the major causes of corrosion is the PH factor of the water supplied by the local municipal. When the PH level of the water is below 7, it is considered as acidic and this causes the pipes to corrode over time from both inside and out. One of the common signs that indicate corrosion in pipes is pinhole leaks. Pinhole leaks cause the water to leak out in small amounts. If you happen to spot such leaks in your water pipes it’s best to get in touch with a professional plumber in Arlington, TX and get your pipes inspected immediately. Ignoring this sign or delaying can lead to serious problems. It can cause your pipes to rupture and break.

Signs of Damaged or Broken Water Pipes

Here are some signs that indicate that your water pipes are damaged and perhaps broken:

• Damp patches on the ceiling and walls
• Frequent electrical faults
• Unusual noises from the water main
• Loss of water pressure

If you spot any of these signs, call a professional plumber in Arlington, TX for inspection without any delay.

Plumber in Arlington TX—Call Benjamin Franklin Plumbing for Pipe Repair

When pipes break or burst, it can wreak havoc in your home or commercial facility. Delaying can cause serious damage to your premises and valuables. For immediate and emergency assistance, call Benjamin Franklin Plumbing service.  They have a team of experienced and well-equipped plumbers in Arlington, TX who can visit your premises and repair broken pipes immediately. Benjamin Franklin Plumbing is a trusted and a BBB accredited company with A+ rating. The company extends plumbing services to both commercial and residential owners and is available at your service round the clock.