Blog

Do you understand how your plumbing system works? Generally, homeowners know nothing more than just the running tap water from showerheads and faucets. Most of us don’t know where this water comes from. Similarly,we have no idea where this water goes off. In short, residential plumbing is complex and extensive. It has many subsystems and components.

So let us have a look at some important information about residential plumbing system. This will help you understand the basics of your house’s plumbing system.

Water Source

Have you ever wondered how do you get water in your faucets? What is itsprimary source? This primary water source may be miles away from your house. This may be miles away even from the local water treatment facility present in your area. Usually, the water that we use in our houses is obtained from lakes and rivers from where it gets directed to a close by water treatment plant by means of pipes laying deep under the river.

Upon reaching the nearby treatment plant, the incoming water is then filtered and gets disinfected by going through different processes until the water is safe for the residential use. The whole process takes a couple of hours as the plumbers in Arlington, TX state.

Throughout this process, the water quality is tested from time to time. This processed water is then storedin a reservoir. From there, it easily travels by means of an extensive pipe network running under the ground until it connects with the water main of your house.

The Water Main

The processed water at the plant reaches your house by means of water main that is usually found close to the front curb. The water gets directed to the shut-offvalve by means of a water meter and from there it enters into your house’s plumbing system.

Do you know that main water valve controls the supply of water into your house? Thus if you ever face an emergency, simply turn off the valve immediately as the professional plumbers in Arlington, TX suggest.

Moreover, get the service of a reputed plumbing company to inspect the problem thoroughly. Mostly these valves are operated by using a key. If you don’t have the key, take the assistance of a local plumber in Arlington, TX to help you out.

The Water Heater

The water heater is one of the integral appliances in our homes. So have you ever thought how do you get the hot water in the water heater tank? What factors are involved in the entire heating process of your water heater?

To get the complete detail about this process, take the assistance e of a professional plumber in Arlington, TX. But for your basic understanding, let us have an overview of this process.

The water in the shutoff valve travels through the plumbing network in your house to the water tank. The tank is at first filled with the cold from its bottom side. This tank is then heated by means of a burner or a heating element. For this purpose, electricity, gas or even a coil may be used as the plumbers in Arlington, TX suggest.

Once the water is properly heated and reaches up to a particular or pre-defined temperature, it starts to rise up inside the water tank and is directed outward from the top side. This hot water is then further transferred to all other areas of your house by means of a plumbing network.

The above-given explanation is only applicable in case you have water heater storage. However, another common option is the tankless water heaters. To take more information on tankless water heater take the assistance of any professional plumber in Arlington, TX.

However, as the name implies, the modern tankless water heater has no storage for water. But these appliances heat the water whenever needed.  This means lower energy consumption and eventually lower bills. If you are planning to install a water heater in your house, then take the professional insight on which one of the two is best for your family’s hot water needs.

Supply Pipes

We all have various supply pipes installed in our homes. They are designed in a manner that hot and cold waters pipes are kept separated. Such pipes are usually referred toas risers and are usually connected to several plumbing fixtures in a house. The hot and cold water pipes run in different pairs in the entire house.

If you live in an old home, your plumbing pipes might be made of galvanized steel. However,in newer homes, copper is used as the main piping material for the plumbing network.

So the question is; should you replace your old plumbing network? If this is not done in a timely manner, you might end up dealing with an extensive water damage issue. So get your system thoroughly inspected by hiring a professional plumber in Arlington, TX.

With that, you must also know the diameter of the plumbing pipes. To get more water pressure you need to have plumbing pipes of larger diameter. If you are receiving weak water pressure, then it’s better to hire the plumber in Arlington, TXand upgrade these pipes into larger diameter ones.

In the bottom line

If you are living in Arlington, TX and looking for the assistance of professional plumbers then head over to Benjamin Franklin right away. Their team of professionals is well versed in handling complex plumbing issues.

Remember a plumbing system is a complex network of your household. It requires a lot of attention in order to function properly. While many homeowners consider the frequent repair and maintenance of their plumbing system, waste of time and money, they must understand that a faulty plumbing system can damage the entire structure of the property.

Thus, hire the services of professionals and get your plumbing system inspected regularly. To hire the services of Benjamin Franklin, you can dial their 24/7 customer helpline number.